(626) 286-0360
Airsoft
Fishing
Air Gun
LCT AK LCK-12 Stamped Steel Airsoft AEG w/ Side-Folding Stock Tube (Model: Standard AEG)
9 Customer Reviews
by Jesse J. on 10/24/2023
"This gun is nicely built however out of the box my example was double feeding due to a bad bucking. LCT's hop units and buckings are known problem parts so replacing both is something I almost always expect to do on these guns.
After replacing the bucking with a Macron from Maple Leaf the consistent double feeding went away.
In order to remove the barrel extension, outer barrel, and sight / gas block from this replica you will first remove the top cover. rotate the take down lever up and pull straight out. Mine came out freely. Pull back on the dust cover while wiggling it left and right. My gun's dust cover was super tight and since the rear sight is on it that's a good thing.
Dust cover should pop off. To reinstall I found it's better and easier to start at the rear then slide the assembly forward and line up the pin hole than it is to line up the pin hole and hinge down. Doing it the later way is difficult due to the tight fit of the sheet metal and the hooks at the rear of the receiver which retain the dust cover.
There are two allen head screws forward of the chamber you will remove and another two allen head screws on the hopup unit. Then you flip the rifle on it's side and knock out the lower handguard retaining pin. You'll know which one it is when you see it as it will have some marring from factory installation. It's the one pin no other AK has on the receiver.
I always go left to right when I remove a pin and opposite for install.
set the hop unit to it's maximum setting and pull forward gently on the barrel assembly. It should separate and move a quarter of an inch. Now comes the fun part.
Flip the gun over and look into the mag well. There's a plate that's keeping you from separating the barrel from the receiver. Use a flat head screw driver to gently bend the two metal prongs that are on either side of the magazine well securing this place then tilt it up and remove. On mine I couldn't bend the plate tabs so I had to tilt and play with the plate and hopup assembly until I could get it to separate.
Once separated pull the outer assembly from the receiver and set it aside. Now pull the hop unit forward until it clears the nozzle and tilt it down then pull it back and over the gearbox. You may have to rotate the entire hop assembly to clear the gearbox.
There's a black plastic tab on the bottom. Pull this out. Then remove the two Phillips head screws on the plastic hop assembly. Remove the sliding arm and flip the hop upside down to allow the arm to swing out the top with the nub. Set the nub aside. Now pull the barrel. It should come out with a brass ring on it and a black bucking. IF the bucking is still in the hop assembly use a punch to gently push it out. Replace with a new bucking then reverse the process.
Once corrected this gun is a joy to shoot and plenty accurate. out of the box my example chronos at 375 with .25 KSC perfect bbs.
As the weapon wears removing the dust cover to install the battery will get easier.
Magazines leave a lot to be desired but Arcturus makes a good AK-12 magazine which can be purchased here on EVIKE.
Overall a good replica of the AK-12 despite incorrect metal finish & lack of accurate trade marks.
After replacing the bucking with a Macron from Maple Leaf the consistent double feeding went away.
In order to remove the barrel extension, outer barrel, and sight / gas block from this replica you will first remove the top cover. rotate the take down lever up and pull straight out. Mine came out freely. Pull back on the dust cover while wiggling it left and right. My gun's dust cover was super tight and since the rear sight is on it that's a good thing.
Dust cover should pop off. To reinstall I found it's better and easier to start at the rear then slide the assembly forward and line up the pin hole than it is to line up the pin hole and hinge down. Doing it the later way is difficult due to the tight fit of the sheet metal and the hooks at the rear of the receiver which retain the dust cover.
There are two allen head screws forward of the chamber you will remove and another two allen head screws on the hopup unit. Then you flip the rifle on it's side and knock out the lower handguard retaining pin. You'll know which one it is when you see it as it will have some marring from factory installation. It's the one pin no other AK has on the receiver.
I always go left to right when I remove a pin and opposite for install.
set the hop unit to it's maximum setting and pull forward gently on the barrel assembly. It should separate and move a quarter of an inch. Now comes the fun part.
Flip the gun over and look into the mag well. There's a plate that's keeping you from separating the barrel from the receiver. Use a flat head screw driver to gently bend the two metal prongs that are on either side of the magazine well securing this place then tilt it up and remove. On mine I couldn't bend the plate tabs so I had to tilt and play with the plate and hopup assembly until I could get it to separate.
Once separated pull the outer assembly from the receiver and set it aside. Now pull the hop unit forward until it clears the nozzle and tilt it down then pull it back and over the gearbox. You may have to rotate the entire hop assembly to clear the gearbox.
There's a black plastic tab on the bottom. Pull this out. Then remove the two Phillips head screws on the plastic hop assembly. Remove the sliding arm and flip the hop upside down to allow the arm to swing out the top with the nub. Set the nub aside. Now pull the barrel. It should come out with a brass ring on it and a black bucking. IF the bucking is still in the hop assembly use a punch to gently push it out. Replace with a new bucking then reverse the process.
Once corrected this gun is a joy to shoot and plenty accurate. out of the box my example chronos at 375 with .25 KSC perfect bbs.
As the weapon wears removing the dust cover to install the battery will get easier.
Magazines leave a lot to be desired but Arcturus makes a good AK-12 magazine which can be purchased here on EVIKE.
Overall a good replica of the AK-12 despite incorrect metal finish & lack of accurate trade marks.
by Marisol R. on 04/08/2022
"Nice and heavy the ebb has a good kick over all a nice gun
by Austin M. on 12/02/2021
"Great gun and quite enjoyable to play with. When i bought it it was 499 bit it just recently dropped to 420 so if your looking for a gun like this now would be the best time to get it
Pros-
-solid steel construction that feels great and will hold up well in games
-very accurate gun from my personal experience
-the full bolt ebb makes for a unique feel more so to a real firearm
-the tight tolerances although difficult upfront will ensure everything stays in place after its broken in
Cons-
-with the bolt in you are limited to 650 rpm (although you can remove it and it fires much faster but you defeat the point of an ebb)
-you have to watch where your charging handle is because it its obstructed it will strip a gear (personal experience)
-it has a very distinct and loud firing noise so as soon as you fire you will stand out.
Overall i love the gun and i have always loved blowbacks so i would recommend it to anyone wanting an ak blowback. Only problem i have had was when i was leaned against a building and fired and now my semi auto doesnt work. I believe its just a gear but i could be wrong
Pros-
-solid steel construction that feels great and will hold up well in games
-very accurate gun from my personal experience
-the full bolt ebb makes for a unique feel more so to a real firearm
-the tight tolerances although difficult upfront will ensure everything stays in place after its broken in
Cons-
-with the bolt in you are limited to 650 rpm (although you can remove it and it fires much faster but you defeat the point of an ebb)
-you have to watch where your charging handle is because it its obstructed it will strip a gear (personal experience)
-it has a very distinct and loud firing noise so as soon as you fire you will stand out.
Overall i love the gun and i have always loved blowbacks so i would recommend it to anyone wanting an ak blowback. Only problem i have had was when i was leaned against a building and fired and now my semi auto doesnt work. I believe its just a gear but i could be wrong
by Steven O. on 07/28/2021
"This ak was everything I expected, it extremely good quality (coming from lct this is obvious) but it is heavier than the real rifle and is extremely accurate it also runs good but Battery space can be a pain in the ass if you don't have a stick type but other than that so far I've has no problems with this gun and I will use it at milsim west's saratov resurgency
by Collin P. on 11/26/2020
"This thing is amazing!
Mines shooting around 425FPS out of the box so it's a little hot for my local field, but it's extremely accurate and being it's by LCT, it has some of the nicest externals on the market.
Battery space is a little tight, so you'll probably have to use stick type batteries.
Overall I highly recommend this gun as the showstopper for any sort of russian loadout, it's already filled that role in mine.
Mines shooting around 425FPS out of the box so it's a little hot for my local field, but it's extremely accurate and being it's by LCT, it has some of the nicest externals on the market.
Battery space is a little tight, so you'll probably have to use stick type batteries.
Overall I highly recommend this gun as the showstopper for any sort of russian loadout, it's already filled that role in mine.
by Matthew C. on 06/19/2020
"I absolutely Love this gun. It feels fantastic I smiled like a kid when I opened it up.
Shoots well , feels solid.
But I did run into two issues. The battery compartment is quite small, and I’ve already had to find a smaller battery.
And the top rail securing pin is extremely difficult to push through, I still haven’t been able to do it after removing it once, to put the battery
Contacting support but besides that. This is a great buy, no regrets.
Shoots well , feels solid.
But I did run into two issues. The battery compartment is quite small, and I’ve already had to find a smaller battery.
And the top rail securing pin is extremely difficult to push through, I still haven’t been able to do it after removing it once, to put the battery
Contacting support but besides that. This is a great buy, no regrets.
by joshua s. on 06/17/2020
"Just what I wanted performs great, few feeding issues at first but I believe that was just a break in period works fine now after a few mags, I like that the AK-15 mags work in it and a few other ones I have tried typical battery space of a AK model other than that I love it
by Jason a. on 02/12/2020
"My first lct, and its absolutely amazing.
Mine shoots at about 412fps so my local field doesnt allow it, but when my team goes to the middle of the desert it works wonders.
Pros
Shoots straight
Beautiful
Weight balanced throughout rifle
Cons
Shoots hot for most fields
Cant quick change spring
Selector lever is a little tight
Mine shoots at about 412fps so my local field doesnt allow it, but when my team goes to the middle of the desert it works wonders.
Pros
Shoots straight
Beautiful
Weight balanced throughout rifle
Cons
Shoots hot for most fields
Cant quick change spring
Selector lever is a little tight
by Christine H. on 02/01/2024
"The gun shoots great and is a really good model of the real thing. it has great weight and the details are very good, however, after very limited use the gun has already rattled three parts off or has damaged them (Kind of expected for a ebb). First the rear sight on the rail, the small pin that holds it down grinded itself off to the rear of the gun to the point that it was sliding up and down the dust cover. Second, the dust cover/bolt, initially the bolt would hang up right at the end of cycling, this was fixed just by shooting again but after careful inspection I realized that the bolt was getting caught on the dust cover because it wasn't sitting right. The only fix was to take the cover off fix the jam and re-pin the cover at a weird angle to allow bolt movement. Finally, the pistol grip just broke off, I wasn't doing anything I just picked up the rifle and held it properly and the grip came off. This has been semi-fixed with some very strong glue but I feel like it might come off again. Hopefully this is just a fluke and I got a defective product as this is my first LCT and my first EBB. I do plan on purchasing another LCT in the future because of the good aspects of this gun and the flaws are more due to the nature of EBB rifles, at least in my head.