"This thing was incredibly amazing for my M16. It was full metal, nice engravings, amazing motor, great RPM, high FPS, all around good.
Works well for M4s and M16s
Heavy( full metal)
Short deans wire protruding from the back
No hopup included
Dust cover stays open, you cannot latch it back so it protects the hopup "This kit is for sure worth the money. The engravings give it a nice touch. The metal is of a really good quality. This is really made for a field gun unless u downgrade the spring like I did and add gears designed for high speed.
-around 420 fps
-no upgrade needed
-lets you build YOUR dream gun
-The wiring sucks; buy new 16-18 gage wiring and solder it yourself
-The motor takes a second to get to max speed unlike a lonex so trigger response isn't the best
-gear ratio is normal which isn't good if u want high speed
-Wired to deans (easy fix with a $10 soldering gun lol)
The gearbox is great if you like tinkering. I've taken mine apart over 30 times and it still works fine. Fare warning, don't try upgrading this with other parts if you don't know what you're doing. If you do, no harm done because there's not a lot you'd have in this kit. Honestly this kit is a great deal by evike. Because evike offers sooo many m4 parts, you are able to build what you want. It makes my m4 seam more personal because I built it from the ground up. Get this kit and you won't be disappointed!--If you want a cqb set up, buy a lonex, high speed gears, an m100 spring, and new wiring (16-18 gage). It creates a SICK weapon and is what i use now! "Its a good starting build for a dream gun and all but I've got a major issue; My rail is half way onto the top receiver. I have a PWS MK112 rail and then I was putting it on it stopped half way onto the receiver. i cant take it off or move it other than if I bash the side of the rail with a rubber mallet to avoid damaging the thing until it is not the right place. i got it upright and straight but now i can't take off the top receiver if I wanted to switch it out, there's a bit of a gap, and doesn't look as nice as i wanted it to. And the wiring to the motor grip is one of those screw on types where you literally need to screw the wires onto the motor which some/most motors do not have so I'm stuck with the stock until told otherwise.
Pros: Good start, high ROF, nice change from plastic to metal, Light (Can be a con)
Cons: My rail, Screw on motor, A bit too light for a good hefty feel, with rail, tube, crane stock, and rail it weighs only 6.48 pounds, Mag wobble, fixable with tape but the inside of the magwell is really rough so it can be tough to pull mags out sometimes. Read More Reviews Write a Review
« Back to product description
G&P Complete M4 Metal Receiver & Gearbox Airsoft AEG ProKit (Seal Team 6) - Rear Wire / Black
Looking to build your dream AR-15 M4 M16 AEG without compromises? The G&P ProKit is dedicated to provide you the top selections of everything you need; and nothing you don't. Every G&P ProKit comes complete with a pre-assembled AR-15 M4 receiver, a fully tuned complete gearbox, G&P motor, motor grip, and integrated deans adapter low resistance wiring harness to start you off without compromises. All that's left between you and your custom dream build, will be a front-end of your choice and stock! The ProKit is a great start for the intermediate and advanced players who want to take advantage of the vast selection of m4 front end furniture and stocks available at Evike.com. The G&P gearbox, motor and receiver is globally recognized to be among the highest rated. Our chronograph, ROF meter, voltage and current meter have also verified that the G&P gearbox runs with lower resistance, a higher rate of fire (given same spring rating) and much smoother as the result of years of research and development G&P put into their performance parts.
Package Includes: Seal Team 6 full metal laser engraved receiver G&P award winning 8mm bearing complete hearbox (Wired to rear w/ Deans) Integrated high performance deans type T connectors M4 charging handle New dust cover set Reinforced G&P metal bolt cover / receiver pin set / forward assist knob / selector / magazine catch Reinforced G&P metal M4 trigger guard / bolt stop G&P M120 motor and motor grip High speed motor pistol grip *If you are looking to build your dream AEG with the front-end, RIS, and stock of your choice: This kit comes complete with everything you need! The gearbox and metal receiver assembly are all pr-assembled! Compatibility:
The G&P ProKit is compatible with all major brands of M4 / M16 series front ends and stocks
M120 (360~450 FPS depending on setup)
Rear. Low Resistance High Gauge Anti-Heat Wiring Harness.
8mm Bearing Gearbox.
G&P High Performance high speed M120 motor.
Established in 1995, G&P is among the oldest Military-simulation and training Airsoft manufacturers in the world. Started as a top combat light provider for law enforcement and military agencies around the world, G&P branched into Airsoft manufacturing with the same belief to never sacrifice quality for lower price. Their motto is visible on every G&P product. Every G&P AEG rifle is hand assembled and individually fine-tuned by top technicians in the industry to match G&P's unparalleled quality and reputation. G&P utilizes CNC precision machining and real-steel finish/coating processes on many of their products.
This item is currently
Out of Stock. Most out of stock items are restocked within 1-3 weeks. Some items may take longer. Please add this item to your wishlist to keep posted on its availability. Wanna chat about
G&P Complete M4 Metal Receiver & Gearbox Airsoft AEG ProKit (Seal Team 6) - Rear Wire / Black?
Have questions about this item? We monitor these comments daily, but it may be faster to
email us directly or call us at 1-626-286-0360.
Facebook about THIS with your friends! Comment for a chance to win awesome airsoft prizes. Details can be found on The Evike Facebook Fan Page HERE! Remember to leave "Also post on Facebook" checked to qualify your comment!