1 to 12 (of 27 reviews)
"THIS MOTOR RUNS AMAZING AND A MUST FOR ANY HIGH ROF SET UPS!
Does not eat up battery
Very magnetic (if bbs were metal I'd be out instantly. Its just really magnetic)
Heavy... for a motor (makes my gun more balanced.)
Did I mention fast
Just one...YOU DON'T HAVE THIS! "Buyers beware, just confirmed that WITHOUT MODIFICATION, this will NOT fit into Tokyo Marui's P90 motor cage (Possibly P90s of other brands as well).
The problem is that the heads of the 2 black screws that secure the base plate of the motor are way too thick for the motor cage to shift far enough to latch back together.
The simple fix I've found is go to a hardware store and look for metric 0.5mm x 10mm screws that have comparably more flushed heads.
Once you got the new screws, simply replace the original black screws ONE AT A TIME (keep one black screw securely in place so you can screw the new screw in without the base plat popping open on you, as you'll need to use some force to fit the new screws all the way down. Once the first new screw is in tight, you can then remove the 2nd black screw and replace it with another new screw, again, make sure it sits all the way down.)
Also, originally there are 2 washers on each of the black screws (4 total), remember to place at least one washer in each of your replacement screws before screwing them in.
Obviously once you've done this you'll void all warranty, so do it at your own risk.
Once it's all fitted together properly, this motor performs flawlessly. If not a bit hot, which's a common problem for all the high speed motors anyway. So try to avoid doing long bursts with these high speed motors installed.
1 star deducted for the fitting problem and time spent replacing screws, but otherwise it works really well. "This is a great motor! The neo magnets are very strong. I put this particular motor in my Echo1 ST6 with a MOSFET and 16gauge wire. The stock motor with a M110 and the upgraded wire setup was getting about 14-15rps (tested with an excortech chrono). I put a M120 and this motor into the gun with a shim job, it now shoots at 23rps! The only problem i had was that the pinion on the motor was slightly to large for the opening in the gearbox, with a quick mod to the gearbox it worked fine.
Its a neodymium motor
Huge increase in rof
Pinion was slightly to large "Awesome high-speed motor. If you're looking for ROF, this is your choice. Is a little loud, but that doesn't matter too much. High quality and super fast, but does heat up quick. It can handle the heat, though. "If i only had 1 word 2 say about this motor, it would b AWSOME! I put this motor in my echo1 scar-L tan and it increased my ROF 250%! B4 i bought this motor, ppl used to make fun of me because of how slow my gun shot. Now there running away and scream after i waste a whole midcap into them in a matter of seconds. This is probably the best possibly motor ever!
EXTREMELY high ROF
Fires as soon as u pull the trigger
NONE!!!!!! YEAH!!!!!! "This is a great motor for high speed applications. I had it paired with a AIM Top Tornado Speed gearbox in an M16 and was achieving around 25 rounds per second with a 9.6v large type. You will want two things with it though: first you'll want a vented motor plate because this motor gets pretty hot (to be expected). second, as everyone else says you will definitely want a different pinion gear. I wouldn't even fool with the stock one as it will strip. I must say though the motor magnets are so strong that when it does the metal shreds will go down and stick to the motor (not all of them, but alot of the shreds). Personally, I was flanking a team with a friend and this stripped right as our postions were compromised which left us totally screwed. Other than the pinion gear its great though.
Very high speed
Pulls up to an M120
Pinion gear is crap
Gets pretty hot "This is a good motor for price but i do suggest buying a new pinion gear mine has already stripped after no more than a few hundred shots. The rof is good as long as you have a weaker spring.
old jg motor with 8.4 m120 spring shot 12-13
old motor 9.6 shot 15-17
new matrix motor with 8.4 m120 shot 15-16
matrix motor 9.6 shot 19-22
this is a decent motor besides a few cons
weak pinion gear
heats up a little fast but not to bad
with to strong of spring the gearbox can lock up so don't use over m120 "Bought this motor to upgrade a GR15 for a friend. It's alright. Like all high speed motors, it heats up quite a bit. It doesn't have a whole lot of torque either, but that's also expected. It does have very strong magnets and is constructed quite well. However, the pinion gear is garbage. Stripped after no more than 500 rounds with perfect shimming to the bevel. New SHS pinion shows no wear after several thousand rounds on the same shimming and set up.
-pinion is crap
-heats up and doesn't have a lot of torque (compared to SHS, Lonex, and AMP high speed motors)a
This motor is something to consider, but the other options tend to be cheaper and slightly better. "Great motor for the money. I haven't used it in a game yet, but tested the fire rate:
7.4v Tenergy lipo - 10 rounds per second
11.1v kong power lipo - 16 rounds per second
7.4v Tenergy lipo - 16 rounds per second
11.1v kong power lipo - 21 rounds per second
This is in an A&K Masada gearbox with a Modify 120+ spring shooting around 390 with .25s.
I'm please as I can now use my 7.4v in the gun as the 11.1v really doesn't fit very well... we'll just see how long it lasts. "THIS MOTOR IS AMAZING!!!!
best buy par none i see some of the reviews on here saying it "can" pull an m120 it will pull it with 22 rps with the Matrix gearbox (with a lipo)
-SUPER CHEAP AND HIGH QUALITY
-THE BEST TRIGGER RESPONSE
-MAKES LITTLE KIDS FRIGHTENED WHEN YOUR NOT ON THERE TEAM "Outstanding performance!
Just a few hours ago i installed this motor into my G&G Blowback MP5A4.
The motor is very well packaged, insulated in a plasic case with foam padding.
Installation is very basic, slipped into place with no problem.
I plugged in my 9.6v 3600 Mah and let 'er rip!
The rate of fire is absolutley ridiculous!
It ripped an amazing ~22 Rps!!
Thats an extreme improvement over the ~13 Rps the stock crappy G&G motor put out.
However, once installed you may need to re adjust your motor height.
Decently power efficent
May need to re-adjust motor hieght after installation. "This motor is just plain super duper pooper epic I mean it's insanely fast when I pull the trigger to my gun everyone is like WOW even the guys with the polarstar's well I get around upper 30's low 40's with this motor m110 16:1 gears and 11.1 lipo and that minimum with the battery not charged all the way
It has pretty strong magnets too so I would even put in a m130
Price depending on you price range but this is a great price for what you get
Over all I would rally recommend you get this motor and get a new heat treated pinion gear because you will have serious fire going down ( you don't have to get one just a suggestion for the future Displaying
1 to 12 (of 27 reviews)
Back to Product Page
Write a Review