Contact Us Tel:(626) 286-0360 Store Locations
Phone Support M-F 7am-5pm PST
Browse by Type or Category
Free Shipping for Orders over $149. EPIC DEALS released daily!

ARES Airsoft Complete E.F.C.S Gearbox Set for ARES/Amoeba Series Airsoft AEGs (Model: Rear Wired)

29 Customer Reviews

by Hezekiah Y. on 10/04/2021
"this made my STG 44 sound intimidating and loud
by Joshua F. on 11/09/2020
"Awesome gearbox will be ordering more in the future.
by Tim W. on 11/07/2019
"Absolutely love these gearboxes. I have built 8 replicas and used them in each 1. The stock gears have held up to a DMR build with a m150 spring without any problems. I recommend them to anyone looking to build a custom replica.
by Jacob c. on 07/02/2019
"Gearbox is great but if you are looking to put this in a Tippmann aeg it will not fit.
by Lawrence B. on 04/04/2019
"I bought this originally to fit into my Mp5 sd6 Cyma. Which I got it in there. Since the mp5 selector acts as the v2 gear box pin and the mp5 selector switch slider is the same as a m4 or m16 I had yo modify some stuff. I tried yo make a selector slide of gift cards. It would have worked well but the Ares gear box has a modified selector slide with a small magnet mounted to it ( for a hall effect sensor) I decided to not even go that route.

Instead I used a 6-32 screw and nut to take the place of the sd6 mp5's pin. I had a broken lower receiver for a m4. So I cut the m4 lower receiver and lined up the pin hole with the mp5 selector switch hole. And marked the position of where yo put the m4 selector on the mp5. I drilled the hole and made it to fit the m4 selector. Now it took a couple tries because the m4 selector hole was not exactly in the same spot yo engage the Ares selector slide.

So I have a random hole in my mp5 lower reciever. But on the second try I got it pretty close and it works.

The 6-32 screw gets in the way of the m4 selector switch because it is not flush with surface of the mp5 lower reciever. A little more effort and it will work great.

Not I used the gun with the Ares gear box installed yesterday. And it worked great. I like it to much because I plan on selling the mp5 and now I don't want to.
by Tim W. on 01/28/2019
"I just received my gearbox today. I put it in my G&F combat machine in about 5minutes. No mods needed. Major upgrade when tested. Love this gearbox.
by Matthew C. on 07/02/2018
"This is a great gearbox for the money. I used a 7.4v 1500mAh lipo and Lonex TITAN supreme motor. The trigger response is fantastic. Out of the box it was shooting about 380FPS with .20 gram bbs.The only issue I have for this is that I couldn't switch it all the way to "Safe". It doesn't fit in my madbull receiver. It does go far enough to engage the safety so it's not really a problem. Besides this receiver is fantastic. Would for sure recommend it to anyone looking to replace theirs.
by Rocky B. on 12/30/2017
"This is a lot of gearbox for the money, with modern features that make traditional gearboxes obsolete. This gearbox makes me wonder why, in 2017, even premium quality manufacturers still produce gearboxes with trigger contacts that burn out, cutoff levers that wear out and fail, and a spring guide design that makes gearbox maintenance a chore. I was so impressed by the V3 version of this gearbox in my Elite Force G36C that I purchased a V2 for my G&P M4. Overall, the G&P box is slightly higher quality and probably a better option if you are looking to build a custom high ROF or high FPS setup, but for shooting out of the box with minimal upgrades I'll take the Ares EFCS all day long.

The only real issue I have with the gearbox is the choice of wiring insulation...it is extremely plasticky and stiff and just a pain to deal with. The wire itself seems to be of acceptable quality but the insulation is just...awful. A thin, flexible, silicone based insulation would be welcome, but is not essential to the performance of the gearbox.

**NOTES ON INSTALLING ARES EFCS INTO G&P M4 RECEIVER**

There is little to no information on what modifications are necessary to fit this gearbox into a G&P receiver...a few vague forum posts and two YouTube videos, neither of which are in English. Here are some notes on what I encountered while installing the EFCS into a standard cast aluminum G&P M4 receiver.

Spring Guide - The QC spring guide is threaded for a buffer tube screw, but the stock G&P screw is too long and will bottom out in the spring guide before tightening up the buffer tube. I used a screw probably half the length of the original and it worked fine, I believe it is an M4 size screw.

Fire Selector Plate/Switch - The Ares selector plate does not move as far forward in the "safe" position as the G&P unit, resulting in the selector switch not clicking into the detente. It stops about halfway between semi and safe. The safety does still function in this position (trigger cannot be pulled), and semi/auto work as expected. Also, if the gearbox is initially installed with the selector switch in the safe position, the rear receiver pin will not fit as it pushes the box too far forward. I did try removing a small amount of material from the U notch in the plate and filing a flat spot on the internal cam of the switch, but I think removing enough material to allow the switch to move fully to safe could result in other fire modes not functioning properly so I left it as-is.

Magazine Release - The "ring" on the front of the Ares gearbox for the mag release to pass through is slightly smaller and more rearward than the G&P box, resulting in a sticky mag release button as it rubs against the inside of the ring. I used a 1/4" drill bit to enlarge the hole in the ring to approximately the same size as the G&P ring and it stopped the rubbing.

General Fit - I did not have to remove any material from the receiver for the Ares gearbox to fit. I did peel out the thin rubber gasket in the rear of the receiver and replace it with a 1mm thick washer to achieve proper nozzle alignment and front to back spacing. With the gearbox installed properly in the receiver, the small receiver pin above the trigger will not fit. The holes in the gearbox are slightly too high to match up with the holes in the receiver and the pin will not pass all the way through. I used a side cutting bit and Dremel to extend the holes downward until the pin fit.
by Rocky B. on 12/28/2017
"This is a lot of gearbox for the money. I was so impressed by the V3 version of this gearbox in my Umarex G36C that I purchased a V2 version for my G&P M4. Having said that, if you are looking to build most epic gun to rek nubs with 50 RPS...this probably isn't the gearbox for you to start with. For shooting out of the box with minimal upgrades it is absolutely worth every penny. The QD spring guide makes opening and closing the gearbox infinitely easier than with a standard spring guide, the microswitch trigger is sweet and clicky and responsive, the EFCS unit provides active braking (always a full cycle) and is programmable with the optional setting box.

**NOTES ON FITTING ARES EFCS GEARBOX TO G&P M4 RECEIVER**

There is little to no information on what modifications have to be made to fit this gearbox into a G&P receiver...a few vague forum posts saying to "remove a little material from the rear of the receiver" and two YouTube videos, neither of which are in English. Here's what I encountered installing the gearbox in my standard cast aluminum G&P M4 receiver.

Spring Guide - The included QD spring guide is threaded for a standard M4 buffer tube screw (M4 screw size I think), but the stock G&P screw is too long and will bottom out in the Ares spring guide. I used a shorter screw, probably half the length of the original.

Magazine Catch - The "ring" on the front of the gearbox where the mag release passes through the receiver is smaller on the Ares gearbox than the stock G&P unit. It is also slightly more rearward, which leads to the mag release button not operating freely as it rubs on the inside of the ring. I used a 1/4" drill bit to enlarge the ring to approximately the same size as the G&P gearbox to eliminate the rubbing.

Fire Selector Plate and Switch - The selector plate of the Ares gearbox does not move as far forward when the safety is engaged as the stock G&P gearbox plate does. Because of this, the fire selector switch will not fully click into the detent for the safety position, it stops about halfway between semi and safe. The safety does function in this position. Also, installing the gearbox into the receiver with the switch on safe will force the gearbox too far forward for the rear receiver pin to fit through. I tried removing a small amount of material from the "U" notch on the selector plate and filed a flat spot on the internal cam of the fire selector switch, but it wasn't enough to solve the problem. Removing more material could have rendered other fire modes inoperable so I left it as-is.

Motor Connectors - I used the stock G&P M120 motor and it has the screw-in style motor connectors, but the Ares gearbox has standard friction fit connectors. I just drilled a small hole in the connectors and used the screw as normal. It's a bit more fiddly, but I prefer motor connectors that can't fall off unexpectedly to connectors that are easy to install but can also disassemble themselves.

General Fit - I did not find it necessary to remove any material from the receiver. I did peel out the thin rubber gasket on the inside rear of the receiver and replaced it with a 1mm thick washer to get correct nozzle alignment and front/rear alignment of the gearbox for the rear receiver pin and mag catch ring. With the gearbox properly installed, the holes for the small receiver pin above the trigger are not aligned with the holes in the receiver. They are close, but just a bit too high and enough that the pin will not go all the way through. I will probably enlarge the holes in the gearbox the next time I have it open so the pin will fit, but as for now it isn't necessary for the stability of the gearbox and is mainly aesthetic.
by Javier O. on 12/19/2017
"Excellent and affordable gearbox for demanding airsofters. Great piece for your tuned-up AEG, or if you want to turn your cheap rifle onto an Amoeba.

Pros:
Good quality, sturdy out-of-the-box gearbox.
EFCS system provides fast, controlled and reliable gear response. No more half-cycles, no more spring overload, no more stuck piston!
Built-in mosfet allows use of Li-Po batteries.
Quick-change flat spring guide makes gearbox compatible with standard V2 AEG's (screw shown in the photo it's just a protector).
Configurable burst mode adapts to different gaming modes.

Cons:
Exterior wiring guides, fragile in order to fit gearbox in lower receiver, ARES should improve that. Proceed with extremely caution.
by Jeff S. on 12/06/2017
"What an amazing gearbox, used it to build a full custom dmr, cyma metal body m4, Angel customs 6.01 barrel, prowin hop up, modify flat nub, prommy flat hop bucking, ares efcs, krytac 30k motor and a 125 spring has culminated in a 430fps laser gun, and the programmer allowing me to lock into semi keeps me legal just about everywhere. Snappy trigger response, consistent compression, good purchase.
by Jorge P. on 09/21/2017
"i love this ares amoeba series gearbox it work realy good with my m4 u may need to change the air nozzles maybe to longe change a smaller nozzles
by Andrei R. on 07/30/2017
"Does it fit to g&p m4 rifles?
by Jorge P. on 05/20/2017
"I like it works ready llipo batteres I love it
by Mark T. on 03/22/2017
"Best drop in gear box on the market for the money. PERIOD.

We have 3 Ares AEGs from stock to moderately upgraded and they all perform at a very high level. They outperform most of the much more expensive guns on the field. I also have a VFC Mk18 and my Ares AM-009 shoots much better with no upgrades. The trigger response has spoiled me.

So.... I decided to use this gearbox on a custom DMR/SPR build. Built a MK12 Style rifle with this gearbox inside. One word. AWESOME!!!! Using a 363mm Mad Bull black python barrel I get about 420fps (.25gr bbs) with no other upgrades.

This is also a quick spring change gearbox which is great for upgrading to even higher FPS, but you will want to upgrade to a high torque motor if you get into the 450fps range of spring for sure.

Looking for a great gearbox? Buy this one!