Contact Us Tel:(626) 286-0360 Store Locations
Phone Support M-F 7am-5pm PST
Browse by Type or Category
Free Shipping for Orders over $149. EPIC DEALS released daily!

Angel Custom Alpha Pro Zero Trigger System For VSR-10 Airsoft Bolt Action Sniper Rifles

8 Customer Reviews

by Diana G. on 05/29/2019
"For those who didn't know. Due to Marui changing their VSR-10 system, there are "Gen1" and Gen2 in the market. This item is made with Gen2 specification and to install on all VSR-10 you should buy the Angel Custom Gen2 Cylinder head too and everything will work like a charm and as expected.
by david b. on 08/04/2014
"I put this bad boy in my JG Bar-10. it fit right in and was ready to play. Had to exchange out the screws which isn't too bad. You really have to squeeze the trigger though even after adjusting.

Pros:
Durable
A touch wont set trigger off
goes right in

Cons:
Might need to replace screws
Little to tight trigger pull
by Austin R. on 03/31/2014
"The cylinder head threads are too long; it bottomed out on the cylinder threads, so I had to use my stock CH. On a positive note, the polymer bushings on the piston are great and removed the tough bolt push I was having with my old Angel piston.
by craig g. on 01/13/2014
"My Ctac vsr-10 developed the slam fire we all know and hate. So this unit looked to be a decent choice as I wanted to upgrade my piston as well. I still don't think 5 days to pick an order is acceptable, but what have you.
This unit came shipped with everything I needed to back into my vsr-10. Took apart my rifle, removed the old trigger and the Alpha fit directly on without any issues what so ever. When it was time to drop in the piston I did have to sand away a decent amount to the delrin bushings to get the piston to slide freely on my cylinder otherwise the piston would stick. Once sanded it went together perfectly. Put it all back together and presto, time ti try it out.
I am using a 130 sprint and was getting about 420-430 stock, with the new piston and same spring I'm now getting about 440-450. The cylinder head seat into my bucking better and I guess thats where the increase in fps comes from.
My only complaint is the trigger itself. It's really sharp, at least this one is, it tore through my gloves after 40 or so rounds. I've since dremeled to to a smoother profile. I would have to say, other than the unit costing 50% of what my gun cost it's a good upgrade and a must have over any stock trigger for a vsr-10.
by Jesse L. on 10/14/2013
"Good trigger, does what it is supposed to. I'm currently running mine on a m190 spring.

Pros
90 degree trigger
comes with matching piston and cylinder head

Cons
Spring guide stopper needed modification
Extremely stiff trigger pull
Piston sear does not always catch
by Paul F. on 06/04/2013
"This trigger seat is slightly off-spec from my JG BAR10 G-Spec. I had to carefully place it to ensure that it lined up with stock screw holes appropriately. It did mesh up, but be advised when installing you will want to seat one screw partially and then start the other. Do not try to do one completely then the other. Also, the stock trigger guard seemed to sit farther away, making the rear screw slightly too short to fully engage the rear of the housing. I had to shave the spacer some and affect a slight bend in the plastic to engage fully. While it has provisions for a safety, the stock BAR10 safety's design is not compatible with this trigger set. As such, if you upgrade, you will no longer have a functioning safety. Additionally, after around 100 or so shots, the rubber tip on the piston detached in the cylinder causing misfires. I have applied super glue to try and ensure it remains intact but have not yet had a chance to retest the piston.

I have been thusfar happy with the performance of the trigger, though it is a rather stiff pull on a 170 spring.
by Jacob B. on 01/05/2017
"I have had this trigger system since the summer. Once I put it in I immediately started having problems. I used it in a Well MB03 which is a vsr-10 system so it should have worked. Everything fit properly but the screws that are use to attached it to the body are too long so it would block the piston if too tight, and the piston would not lock back if too loose. I had to tape down the screws at the right position so the piston would lock properly. Once I fixed that problem I had another. The rubber piston head would rip off of the end of the piston, creating a vacuum in the cylinder. I had to take the whole assembly apart multiple times to fix it. I ended up cutting the thin end of the piston head off and super gluing the rubber piston head to the piston. Once I got these problems fixed however the rifle was able to perform reliably. The trigger pull is a little stiff but it still works fine.
by Jacob B. on 01/05/2017
"I have had this trigger system since the summer. Once I put it in I immediately started having problems. I used it in a Well MB03 which is a vsr-10 system so it should have worked. Everything fit properly but the screws that are use to attached it to the body are too long so it would block the piston if too tight, and the piston would not lock back if too loose. I had to tape down the screws at the right position so the piston would lock properly. Once I fixed that problem I had another. The rubber piston head would rip off of the end of the piston, creating a vacuum in the cylinder. I had to take the whole assembly apart multiple times to fix it. I ended up cutting the thin end of the piston head off and super gluing the rubber piston head to the piston. Once I got these problems fixed however the rifle was able to perform reliably. The trigger pull is a little stiff but it still works fine.