Contact Us (626) 286-0360 Walk-In Superstore Daily Deal
Extended Holiday Phone Support M-F 7am-6pm PST
Browse by Type or Category
HAPPY HOLIDAYS - 25% OFF   Use code: NEWLOOK

Evike.com Moondog Industries Universal Gas Fill O-Ring Set for Airsoft Gas Gun Magazines

31 Customer Reviews

by Jordan M. on 07/21/2016
"these are good replacement o-rings, just be careful as they are extremly hard to fit in the tm fill valves
by Tim G. on 03/12/2016
"I you buy a KWA pistol mag order some of these you will need them . They work great .
by Loren M. on 12/21/2015
"These are great!! I used them in my KWA M9 mags after finding that a bad nozzle on a can of gas had broken and wrecked the o-rings. I used these as a replacement and they work great. That all I can say.
by Connor H. on 10/20/2015
"LOVVEEEDDDDD IT!!!! My kriss vector has been shotty with the mags for about 4 or 5 months and i tried everything and saw these. Now, no leaky fill! would buy 100x over
by Scott B. on 06/14/2015
"Very happy with these. I have replaced the fill valve o-rings on my KWA KP8 mags (3 each) and my KWA KMP9 mags (2 each) and there is absolutely ZERO spilling from filling even starting with a full can of green gas.

They are somewhat difficult to replace, but I haven't had any tear like what people are saying. Comparing them to the stock KWA charging valve o-rings, they are much thicker and higher quality. I got plenty of leaks with the stock KWA o-rings but none with these.

Here are the steps I take to replace them:
1) Get a sewing needle and poke the o-ring and twist until you get and edge to pull it out.
2) Drop some silicone oil down into the valve.
3) Place moondog o-ring on top and use a pick (not very sharp) to spread around valve.
4) Drop more silicone oil on the top of the o-ring and test fill.
by Bradley B. on 12/11/2014
"Nice O-rings. They do the job they are supposed to. I have not had any O-rings break yet. I stretch them slightly by rolling them on a tooth pick before installing them.
by Juliet C. on 05/23/2014
"GET THIS RIGHT NOW you will not regret it you can save any gas mag that wont fill with this amazing o ring i use them on all my gas mags
by Mike R. on 01/01/2014
"Work great, fit nice and snug in my gbb pistol mags!
by Dan F. on 09/28/2013
"These O-Rings are great. I recently bought a m1892 lever action rifle and upon arrival the gun had issues with filling. Gas would just spray everywhere. I purchased these and replaced the o-ring and it is filling perfectly and shooting great. I highly recommend these o-rings for anyone that owns gas powered guns. They are very handy.
by Marek P. on 09/03/2013
"Good product:

Pros - now I have no gas leaks during filling up the KSC G19 mag
Cons - on one mag, the o-ring - due to its thickness - caused light gas leakage. I fixed it by oiling the o-ring

You canīt go wrong with this one!
by Ryan R. on 05/12/2013
"These o-rings fit in KJW M9 clips I had the clips o-ring fail. Install it just like in the video but before you put it on spray some silicone lube on the o-ring and the nozzle. This ikke make it very easy to install and help make it last a long time.
by Joseph F. on 05/06/2013
"Bought these O-rings for my old Glock34 mags. I thought I had to buy a new fill valve, but all they needed were filler O-rings. Make sure to use some airsoft silicone spray/oil to lube the O-ring and the fill valve; they will go on super smooth and you will not tear any O-rings.

Install them just like the video by using two tooth picks. Just add a step, and oil everything and they will slide in easier and you won't tear any. After installation, there is no leaking when filling whatsoever.

Pros:
-Nice and thick O-rings
-Universal
-No leaks at all now!

Cons:
-Just make sure to oil the O-ring
by brett r. on 03/07/2013
"Fantastic o-rings! If you want o rings that wont cause green gas to spray out while filling your mags this it the item for you!

Pros: Easy to install
Prevents green gas from spraying while filling
Don't fall out like other o rings do!
Red color makes i easier to see.

Cons: little expensive but totally worth the quality!


Note* These will not fit in all type of valves.
by Justin K. on 12/01/2012
"These are pretty good o-rings. They do their job. However, remove the fill valve and place some gas line seal tape (the yellow one) around the threads and your magazines will not leak, ever. I've gotten over 40 shots on a single fill of an almost empty can of green gas using this and the moondog industries oring.

Like the previous guy, expect to rip about 3 o-rings before getting it in. I find the best technique is to start on one side and push the o-ring as far down as it can go, then using an allen wrench or toothpick, stretch it around the part where you put your nozzle in. Don't try to get it all in at once directly from the top. They will break.

Excellent product. Only $5. A must if you have GBB's!
by Nadine L. on 08/18/2012
"These work perfectly. If you have a gas gun, buy them. If you dont and think you want one, buy them.
Dont listen to any of these other people, they are extreemly easy to put on, they must just be dyslexic or something. i used two toothpicks and it took the better part of ten seconds.