Contact Us Tel:(626) 286-0360 Store Locations
Phone Support M-F 7am-5pm PST
Browse by Type or Category
Free Shipping for Orders over $149. EPIC DEALS released daily!

Guarder Enhanced Loading Nozzle for Airsoft Gas Blowback Pistols (Type: Tokyo Marui M1911)

15 Customer Reviews

by Everett S. on 11/20/2021
"Haven't had any issues and it is very solid
by Dean C. on 09/05/2018
"Best nozzle ever, you dont even need to buy a seperate flow valve. Get it!
by Austin L. on 09/16/2017
"Great replacement if your original nozzle breaks!
by Mauricio F. on 01/22/2017
"Hola soy nuevo en esto y quisiera saber si sirve para la aps acp 601 pistola co2 gracias
by chris r. on 10/23/2016
"One of the best nozzles for the G platform. Combined with the guarder seal it provides an airtight connection to magazine and around the BBU. no loss of air, consistent crisp and decisive blowback.

Works best with WE flat gas route seals as the nozzle base itself isn't curved like most others. Evike sells the WE flat mag seals. Way better than the curved marui design (and aftermarket curved)
by Marco d. on 04/11/2012
"The Part cracked after a couple of games, but Evike replace and shipped it free of charges.
It only took 2 days between my first email, to Evike shipping to me.
The parts are not made by Evike (so no fault to them it cracked), but they are 110% behind "customer satisfactory".

Thank you Evike. I will buy and recommend again.
by Marco d. on 02/24/2012
"This is a great addition to my hi-capa 5.1.

Pros:
Fits perfectly into my WE Hi-Capa 5.1
Much sturdier then the original Nozzle.
Feels like the nozzle is tighter against the inside rubber ring.
Feels more powerful.
Sounds even a little different.

Cons:
It does not come with the inside parts (valve, spring etc.) Just by removing the very small screw, and putting it back, since all the parts inside are plastic, it stripped. Does not seams to matter, the metals parts attached to the blowback housing seams to hold everything together.

P.S. evike has the fastest shipping department. Took 2 (two) days to ship this part, from California to Florida, Thank you evike.
by zachary r. on 12/01/2008
"Hey does any one think itll be possible to rig this to fit my scar?
(I'm tryin to make my gun look like the Masada Assault Rifle)
by Matt J. on 11/21/2008
"I have the one that doesn't have any rails, which is the same thing just, well, no rails! However despite that, my G36e broke down and now I need to rebuild it and will use this. With this kit you can make your G36 virtually any roll weapon in your squad. A bipod would be very nice for snipers or machine gunners, and the rails make this incredibly easy to attach any design versus the G36 specific one. Also an M203 will make you a squad grenadier or a heavily armed assault rifleman or just give you that extra firepower most G36's this size won't have. For $85? Why not? You buy versatility with this and expandability for your gun. Instalation's a snap, just unscrew your C or K barrel setup from the mount(for the C it's just the flash hider and the K is a small outer barrel) and then put the extension on and put a 510mm tightbore 6.05mm or tighter inner barrel with a metal hop up chamber and you're set to put some very effective bursts down range farther than your buddies with their precious M4's or MP5's by a long shot. The largest downside however, is its size. With this, it's not in any way a CQB or indoors rifle; take it from me I have tried and failed! Get one of those MP5's or any SMG for that model, or better yet, buy another barrel mount and keep your G36c parts for a hot swap that only takes a screw driver and 5 minutes to go from CQB to long range support sniper/machine gunner. All in all, yeah this is a somewhat expensive upgrade but it's worth it if you really consider what you can do with it; if a G36 is your choice rifle, and you want something bigger, better, and more accurate, pair this up with a 510mm 6.04mm tight bore barrel, metal hop up and some matrix high grade .2 or .25g ammo and once adjusted, my G36 with that near exact same setup save for a plastic hop up, was reaching 200ft accurately with .2g ammo. This will do that, with rail expandability! Hope you enjoy, and this is definetly a killer G36 part.
by Trent B. on 04/21/2021
"Sadly this does not fit in my we-tech hi capa (the series named after dinosaurs i believe) well built and will probably do good in tm, but doesn’t fit in my we. Will update if it fits my salient arms hi capa.
by Sang L. on 01/22/2019
"I wish they made the loading ramp more durable it bends
by Robert K. on 06/09/2018
"This was a suitable replacement for the KJW P226 nozzle. My original nozzle's loading pin started to flex in warm weather and thus because useless. This one does not include the air valve. You will need to pull the one out of the old nozzle. You will notice that the retention pin holding the valve on the KJW nozzle goes through sideways, whereas this one has the retention pin going in vertically. I had to file down the head of the pin and then super glue it in place to keep it from scraping against the roof of the slide frame. You may also need to sand the top of the nozzle down to prevent scraping as well.

Another note, the WE P226 nozzle is not a suitable replacement for the KJW P226, as it is much wider and will not fit within the frame. I would imagine that this Guarder nozzle will not work with WE's P226.
by keith e. on 05/06/2017
"does not fit t rex high capa
by matt r. on 01/31/2010
"Zach... I dont own this kit but to answer your question is NO... this will not fit on a scar...
lust answering his question webmaster...
by Morgan H. on 01/06/2020
"This is not a blowback unit. it is just the shell of one it comes with no internals whatsoever even though that is not listed anywhere on the page. evike's customer service is the only thing worse than this I have emailed 3 times to try and get this rectified and have never gotten a single response. DO NOT BUY THIS