ID: 62944 (Mag-APS-AC045)
Hover or touch above to zoom
MAP ProtectedExempt From Coupons
- Metal alloy construction
- High tension spring ensures reliable feeding
- Easy to remove base plate allows for easy access to CO2
- Reinforced polymer lip
- Designed specifically for APS D-MOD series Airsoft Pistols
For APS D-MOD Series Airsoft GBB PistolsCapacity:
12g CO2 CartridgeManufacturer:
California residents click here for Proposition 65 warning
(Write a review)
"Worked great, and fed well. Picked up for a Hornet, and ran like a beast.
One c02 cartridge went strong for 4 full magazines, and still had pressure.
"the end cap of this co2 mag. is 2 tone brass ( outer ) & silver ( inner ) the silver center screw is to pierce the co2 capsule only. that is its only purpose. it does not transfer co2 from the piercing pin to the exhaust valve like a normal co2 mag works . once it pierces the co2 capsule back the silver inner piercing screw out about 3/4/ to 1 full turn the co2 in the 12 gram capsule will then fill the inner portion of the magazine. the co 2 inside of the mag. will then travel upward to the hole inside the mag that feeds co2 to the exhaust valve.
Forget all you know about a regular co2 mag . where the pin not only pierces the co2 capsule and feeds co2 directly to the exhaust valve. the APS co2 mag becomes the co2 tank itself . Also when a co2 capsule is turned upside down and then pierced the co2 comes out of the capsule in liquid form and as it fills the APS magazine ( while traveling from bottom to top) it turns to its gas form filling the inner cavity of the APS magazine. when you remove the piercing cap look inside of the mag and you will see the exhaust valve feed hole. this is what makes the magazine work so well knowing it"nomenclature, this clarifies my last review of this magazine I hope this helps all who are having problems with this type of co2 magazine.
"so far I love these magazines, they are an engineering marvel.
But there is a trick to getting it to work as it should.( 1st lubricate the entire unit with a good silicone spray oil made for air soft guns )
When you 1st. receive the mag. you will see an inner silver screw and an
outer brass colored screw . Take the small end of the key and unscrew the center silver screw out until it stops ( do not force it past the point where it stops or you will or could damage the mag.) turn the center cap in and line it up with the key grooves on the brass cap. insert the co2 capsule, inverted into the magazine screw the piercing cap on by hand until it seats . take the large round end of the key and screw the assembly in until tight . Turn the key over to the narrow end and insert it into the center ( silver screw ) and tighten until the co2 is pierced, after you hear the co2 tighten the center screw until tight and then back it out about 1 full turn ( I have found that this takes no longer to do than a co2 mag that uses a steel threaded end cap with hex wrench.)
After this method is followed the mag. itself becomes a co2 tank letting out a pre measured amount of co2 via the exhaust valve giving every shot an equal amount of co2 per shot
I hope this helps to better understand how the mag works.
I did receive 1 mag that leaked at the exhaust valve .I called Evike and Ken sent me a brand new one should be here in a day or two.
Thanks Ken and Evike
Discuss about APS 23rd CO2 Magazine for ACP D-MOD Series Airsoft GBB Pistols - Black with your friends and fellow Evike.com shoppers!
Comment or answer questions for a chance to win awesome prizes.
Details can be found on the Evike.com Facebook page.
Remember to check "Also post on Facebook" to qualify for the giveaways!
Have an urgent question about this item? We monitor these comments daily, but it may be faster to email us directly or call us at (626) 286-0360. Our resident experts are standing by to answer your questions!