ID: 61583 (SR-MB01-OD-PKG1)
Hover or touch above to zoom
No Payments + No Interest if paid in full in 6 months through PayPal Credit. Simply check out using PayPal and select PayPal Credit!
*Bipod shown in images not included
Shadow Op MB01 Type96 MK96 APS-2 Airsoft Bolt Action Sniper Rifle - OD Green (Add 3-9x40 Scope)
- Heavy duty metal barrel and bolt assembly
- High strength polymer stock
- Comfortable rubberized butt pad
- Accurate, adjustable hopup
- Top rail for optics
- Detachable front 20mm rail block for bipods and accessories
- Large selection of aftermarket replacement and upgrade parts
415~425 FPS (Measured with 0.20g BBs)Fire Modes:
Single Shot, Bolt ActionSystem:
Spring Power, APS2Package Includes:
Gun, Magazine, ScopeHopup:
(Write a review)
"This is a good gun, but please read the rest of my review.
I got this my upgrade to my UTG SOFT-M324 Gen 5 Master Sniper. That is a nice gun but I never should have wasted money on it because upgrading it is a pain in the rear. You can upgrade everything on the the MB01 except the stock, LOL. Everything. But first...
Is it confusing? Heck yeah it is! Is this an L96, an MB01, an APS2 or an S368? Made you look! No one knows, that's my conclusion. Yes, No, All Of The Above.
Out of the box: It goes together very easily. The speed loader comes with a little thingy that helps you shovel BBs into the MB01 mag. It's funky but it works fine. The first thing I did was load it up and fire a few. At 30 feet I was getting a 2" group using Cobb's .28 BBs. That's right out of the box with a dirty barrel. I noticed right away that it does not have the FPS of the M324. Not surprising as it's barrel is much longer.
Next, I took it apart. You really want to be careful when you do this.
*** Important *** If you don't intend to upgrade this gun soon I highly recommend that you not open it up! There is really no need unless something crazy is going on. That, and use good, polished BBs. It's the single best thing you can do for any AirSoft gun!
First I removed the barrel from the upper receiver. Loosen one small allen and unscrew the barrel. No big deal. It comes right apart and, contrary to internet myths, there is not too much oil or grease on anything. Remove the magazine guide attached to the barrel with a small phillips head and it slid right out. Brass barrel with two cheeseball spacers. You want to tape these in place. The HopUp is a basic one piece unit. The adjuster is a fairly coarse affair so a little turn can go a long way. The barrel is held in place in the HopUp unit with a pressure fitting that you can loosen with a small crescent wrench. Don't bend the barrel... if you remove the barrel from the HopUp you need to take note of the brass washer you will leave behind in the HopUp. Not much to see...
Next I wanted to see the cylinder. * Caution *. Remove the bolt housing with an allen wrench (it has thread tightener on it for a reason). When it is removed you want to carefully pull the piece that it secures back and off. There are small pins in the bolt and bolt holder that you want to pay close attention to. Pull it apart slowly and carefully and note the exact location of everything. Really.
I pulled out the cylinder and glanced at it - not too much grease. I didn't open it up.
I put everything back together.
My conclusion is that A) don't do this unless you are confident. B) they took care assembling it wherever they do this so that you have a usable rifle right out of the box. I didn't take any special care re-assembling it and the quality of the pieces shows. It works fine but I need to make sure I return the bolt solidly to make sure the BB is seated properly or else it will totally jam and freak out. Tightening the bolt holder by 1-2 thousands might fix this.
My recommendations: 1) Upgrade Barrel to 6.01mm SS and HopUp to an AEG version with new Bucking. 2) Metal Trigger 3) Upgrade Cylinder, Spring and Piston (with head to match HopUp).
That's my plan and I predict I will have a monster that places .28-.30 BBs with crazy accuracy and FPS.
Accurate right out of the box.
Plastic trigger is really good with a solid piston guide. Really. I hope a metal upgrade can match it.
Easy to dis-assemble.
Easy to re-assemble.
Easy to Upgrade (and you will want to).
Mine didn't come with a cleaning rod, just a plastic thingy that can slid down the barrel and clear a jam, not hold a cleaning cloth.
While I haven't adjusted it, the Allen Screw that adjusts the HopUp seems too loose and coarse. If you can't upgrade I would add some thread seal to this ASAP.
The rail adapter that attached to the front of the rifle in unforgivably loose fitting. I rolled my eyes at all the reviewers that mentioned this until I got this gun. Given what UTG does and is capable of, they should have just made a decision to re-machine this piece so it fits properly. I wrapped some tape on mine...
"Eh, an OK gun, I would not recommend it, but it shoots well. The plastic body and cheek pad broke very easily, and the under barrel is EXTREMELY wobbly. Hop up is the worst I've see. Ever.
Shoots well (accurate and powerful)
springy mag ejection
Bolt action is smooth
Hop up is difficult
Not very durable
Speed loader doesn't work very efficiently and doesn't connect with mag well. Expect A LOT of dropped bb's
says MADE IN CHINA in white letters across the body.
Came with a missing bolt. (Chinese manufacturing probably)
"I recently purchased this item it's not that bad the only flaw i have with this is the under rail it's realy wobbly.
over all rating 4/5
Discuss about Shadow Op MB01 Type96 MK96 APS-2 Airsoft Bolt Action Sniper Rifle - OD Green (Package: Add 3-9x40 Scope) with your friends and fellow Evike.com shoppers!
Comment or answer questions for a chance to win awesome prizes.
Details can be found on the Evike.com Facebook page.
Remember to check "Also post on Facebook" to qualify for the giveaways!
Have an urgent question about this item? We monitor these comments daily, but it may be faster to email us directly or call us at (626) 286-0360. Our resident experts are standing by to answer your questions!