"I bought this gearbox just under two years ago and it has served me well up to this point. I'll start with the good things about it. All of the internals are very strong and well made, however I have had to replace the spur gear due to a tooth fracturing off of it. While the internals are very good that doesn't matter at all if the gearbox shell isn't built well, which it is not. One week ago the front end of both halves of the shell fractured right off where this piston hits the cylinder head. This is a horrible gearbox in terms of longevity but when it works it works well, This gearbox has been run completely stock except for a change of gears due to the tooth fracture, I put in JG standard gears as a replacement. I do not go airsofting every weekend so this gearbox did not see extensive use, I usually go every 6 weeks or so. This break will render your gun useless and will cause stress on the hop up if you do not find the fracture in time. This may also cause your hop up to break leading to many headaches as I have experienced.
Would I recommend this? NO-NOT EVER, Unless you plan on only going airsofting once. I am being dead serious-DO NOT BUY THIS. "5/5
Absolutely wonderful. I bought this with the Matrix Magnum 3000 motor, performs like a dream.
First thing I did with it was void the warranty by opening it up. Inside, lots of nice parts. The spring guide stainless steel, as is the cylinder head. Unfortunately, the selector plate did not have contacts, and the wiring set didn't have them for the selector plate either. Wah. Didn't matter, cuz I bought a MOSFET system with a trigger set included, and I had a spare selector plate with trigger contacts. Works very well.
Has what the picture says inside.
Pre-shimmed gears. If you open it up, make sure they don't go flying off so you know where each shim was.
Powerful, well worth the price.
Wiring is extremely short, not even an inch out of the gearbox. If you try to fit it in your lower reciever, the tamiya connecter will probably rip off. It did for me.
No trigger contacts on the selector switch or corresponding ones on the trigger set.
Overall, a very nice gearbox, with a 363mm MadBull V2 6.03mm, madbull ultimate hopup, MOSFET, and this gearbox well outperforming a KWA SR10 without upgrades. "I got this in the mail today and started building my AEG from scratch(almost).I'm really glad I got this pre-assembled gearbox, a little greasing and my gun was shooting amazing. Saved a lot of time. Only con is the wiring in the back was too short - would have rather seen regular wire crimps instead of a small male tamiya connector. After ripping that off all was good. Great product.
Suggest that you buy it with some extra wiring. Read More Reviews Write a Review
« Back to product description
Matrix / AIM Lipoly Ready 8mm Complete Gearbox Set for M4 / M16 series Airsoft AEG (Monster Torque) - Wiring to the Back / Stock
*Motor Not Included / Sold Separately. Recommended Matrix Magnum Motor.
For Experienced players only. This complete gearbox set is essentially a pre-assembled complete reinforced / tune up kit for your M4 / M16 series AEG. Manufactured by Matrix Tactical Systems, one of the most established, reliable and well known Airsoft manufacture in the world. This gearbox is an affordable alternative over the Systema gearbox with 8mm bearing sets. The
Mecha box shell is modeled after Systema's new gearbox design with thickened shell. With the more stabilized 8mm bearing set, this gearbox is more attractive than ever!
Matrix Tactical Systems. OEM: AIM. Matrix is the exclusive US Distributor for AIM Products.
Tokyo Marui, Classic Army, Echo1, JG, G&G, G&P, Echo1, DBOY, SRC, A&K, KWA and compatible models. Modification might be required for certain brands.
Matrix Tactical Systems Gearbox Models :
Available in Monster Torque and Tornado High speed. Front wire and rear wire.
- Systema / G&P / Classic Army Type 8mm Enhanced "Thick Type" Mecha Box Shell.
- M120 Spring. Velocity out put for this gearbox is around 400~440 FPS.
- Low Resistance / High Capacity / High conductivity / Wire & switch assembly Set.
- High Grade 8mm Metal Bearing Set Installed. Providing enhanced stability over the 6mm and 7mm gearboxes
- Ball bearing CNC Stainless metal spring guide.
- Matrix Ultra High Performance High Speed Piston with Metal full teeth strip.
- CNC Stainless Steel Cylinder Head.
- Reinforced Silent Polycarbonate Piston Head.
- Steel Gear Set
- Reinforced Nylon Smooth Selector plate and tappet plate.
- Reinforced Ball Bearing Polycarbonate Piston Head.
- Reinforced Matrix Monster (Torque Up) Gear set Installed.
Complete Gearbox Disclaimer:
We have compiled a series of videos for AEG take down, assembly and gearbox for your reference. Recommended for experienced players only. A "gearbox" virtually never breaks, Evike.com offers spare parts for all components. All gearboxes are sold as complete set of parts and "AS IS". All the gearbox are directly from manufacture. Buyer responsible for fine tuning and proper installation. Evike.com is not responsible for shimming it perfectly or playing the game of airsoft for you.
For more information on complete gearboxes, please visit:
Complete AEG Gearbox Review:
A good gearbox on par with the KWA M4 gearbox. One advantage of this gearbox over the KWA is that all 6 bearings are standard size 8mm bearings you can buy. Making it much easier to work on. The monster gear set can power up to M170 spring combined with magnum motor. The inner wall of the gearbox is reinforced, just like the Systema new type
Mecha box shell, with all the inner walls thickened. Easy installation for most major brands of M4 / M16 series AEG. Great performance.
To install this gearbox on a MOD5 series, although it is a version 2, the nozzle, selector plate and trigger are not the same. Slight work and gearbox knowledge will be required.