ID: 30700 (B-X025)
Hover or touch above to zoom
For Tokyo Marui, Matrix and Echo1 P90 / E90 series Airsoft AEG.Kit includes:
factory P90 body, fire mode selector and and magazine catch.Manufacture:
JG / Matrix / Echo1
California residents click here for Proposition 65 warning
About JG / ASP / GE
JG / Jing Gong (China) / ASP (Hong Kong) is among the world's largest Airsoft OEM (Original Equipment Manufacturer) and pioneer for high quality Airsoft AEG rifles. With superb production capability, volume, and their close relationship Evike.com positioned JG to provide the world market with great reliable products.
(Write a review)
"I hate writing less than stellar reviews for Evike, because they've been really good on helping me out with the returns.
But I must say, the P90 body they gave me, did NOT fully connect with my King Arms receiver, I had to JAM it in and it STILL would NOT go all the way in leaving 1/4 an inch left before it can click, and it basically got STUCk at this point.
The king arms mechbox, DOES FIT GOOD, however the body didn't even come with a metal bracket for the trigger to reach the mechbox, therefore it doesn't even fire.
I don't know if evike left out the metal bracket for the trigger, or if this particular part just doesn't even come with one, but either way this batch will NOT allow you to fire when pulling on the trigger!
When i had to HAMMER my receiver back out (holding only the body and the hammer), the receiver after 5 hard knocks it then fell on the floor hard and broke my hopup, it's not evike's fault, BUT had this thing moved out smoothly as it's supposed to it would have never happened because i would have both my hands on the receiver and body to GENTLY slide it out.
The body requires major sanding to get the buttplate and receiver to fit in, for some reason the body i received for my order is too tight, and doesn't come with the metal bracket NECESSARY for the trigger to reach the mechbox.
I give this a 3 out of 5 stars because I know evike will never have this problem happen again after this review (hopefully), and make each new batch come with the PROPER trigger components.
"I might as well give this 5 stars since it's not like you're going to find it anywhere else anyway. Basically, it does it's job. Quality control in the details is non-existent, but its overall build quality is slightly better than the JG/E1 P90s (some parts in the back are re-enforced/ glued. When they say this is a replacement body, they mean it. the only parts of the stock receiver that come with it are the fire selector, trigger, mag catch, and the two metal bolt pieces in the back; it doesn't even have the fake ejection port for Pete's sake. Not too much of a problem if you remember to salvage the following parts off of your old body (unless you want this for paint jobs): the butt plate, the fake ejection port piece I mentioned (on the bottom behind the grip), the hop-up access door, and the metal trigger bar (the one that connects the gearbox and the actual trigger). Going back to what I said about the quality control in the details, there were several. First, (a downside of the re-enforced-ness) a regular 8-cell airsoft battery didn't fit into the battery section anymore due to a piece of re-enforcement plastic that sticks out in the back (going to have to switch to the "L" type/ P90 specific batteries). The mag catch didn't fit completely with my mags because it was too thick in some areas (take dat Xacto knife to it!). the fire selector didn't make as positive a "click" when used (again, Xacto knife!). Finally (and probably the biggest problem) the notches in the fire selector that decide how far back the trigger goes (and whether or not you're firing full or semi-auto) is cut differently from my stock one. It doesn't let the trigger go far back enough for semi auto. The solution to this should be simple (if it works, I haven't tried it). Try to wrap duck tape around the end of the metal trigger bar thing to make it longer.
That's the gist of it. Sorry for making this a review/solution segment, but again, you can't find this (or reviews for it) anywhere else so I tried to be as helpful as possible. I hate how people take advantage of how hard it is to find P90 stuff.
"great thing this is. just ordered it. from my research it's good for two things. multiple paint jobs on your p-90, and replacing cheap non-trademarked stocks with good ones. great pricing, best i've found actually.
Discuss about Replacement Body / Stock for P90 series Airsoft AEG (JG Echo1 Marui FN Herstal King Arms CA) with your friends and fellow Evike.com shoppers!
Comment or answer questions for a chance to win awesome prizes.
Details can be found on the Evike.com Facebook page.
Remember to check "Also post on Facebook" to qualify for the giveaways!
Have an urgent question about this item? We monitor these comments daily, but it may be faster to email us directly or call us at (626) 286-0360. Our resident experts are standing by to answer your questions!