"The M1919A4, currently made by EMG, is an interesting weapon which will have a limited, but devoted fan base. I purchased mine from Evike and it arrived about a year later, after numerous production delays. That is to be expected with unusual guns, especially larger guns like this one. The wait was worth it.
The gun arrived in a nice, well packaged box. All the parts were secured and totally intact, as opposed to the Viva Arms M1919 I bought from AirsoftGI, a few years ago. The construction of the gun appears to be identical to the Viva Arms gun with the exception of the EMG using a Matrix M249 gearbox and having a easily removable barrel jacket and muzzle.
The gun, judging by the tags and labels, appeared to be assembled by Evike. There were odd bits of paper with "Evike" written on them, inside various assemblies of the gun. There was also a tag stating the test fire results, FPS and ROF. I gave the gun a look over and set it up on a tripod. The ammo box is similar to the Viva Arms gun, but it slaves off the trigger for feed signaling. It also uses a collar with set screws to attach the feed tube to the hopup chamber. Both are definite improvements over the Viva Arms gun. The box tray, which mounts to the side of the gun isn't really proper unless the gun was vehicle mounted. It is needed to keep the feed system effective, but it limits the traverse of the gun.
Well, the gun was ready to go. I fired .20g BBs through it. They spit out the muzzle, going about 20 feet before falling to the ground. There was no hopup to adjust, so it was time to open the gun up and find the problem. Upon disassembly, I found the air nozzle was split in two pieces. I also found the fixed hopup was not aligned properly with the barrel.
I did two things to make the gun work. I opened up the gearbox and replaced the nozzle and made sure the gears were shimmed. The next step was to take the plastic hopup chamber and drill a small hole above where the hopup hole is located on the barrel. I threaded the hole and installed a 6-32 set screw, which gave me an adjustable hopup with the set screw acting as the hopup nub. I installed a Promethius tight bore barrel, which was a bit longer than the original barrel by about 30mm. This brought the inner barrel clear up to the base of the muzzle, giving it stablization. I reassembled the gun, set it up and gave it a shot. The BBs now fired out at least 150 with great accuracy. Problems solved.
The traverse and elevation unit, which must be purchased seperately, is a quality bit of machining which makes the VA version look homemade. The gun does come with a pintle, which is also well machined. It seems the pintle offered seperately by Evike, does not fit. The main bolt seems to have been copied from a tripod used for a .50 cal M2, as it is too large to fit through the pintle ears of the M1919. I used a replica tripod from another source, so I cannot comment on the EMG product.
While these special production guns usually need some attention when they arrive in the hands of the end user, the EMG gun was a good improvement over the VA gun. The adjustable hopup was an easy modification. The stock parts will work fine but you may wish to upgrade as they fail. The M249 gearbox seems like a stout unit and easily upgradable. The finish on the gun is good. The barrel jacket may look better in a grey parkerized color instead of the glossy black it comes with. The sights are fine. The rear sight is adjustable but the peep hole was not cast in the sight block. It was easy to disassemble and drill a hole in the sight block, to get a more realistic sight arrangement.
All in all a good gun. Some minor mods and upgrades with make it excellent. "Basically, when buying this machine gun, you are paying for the unique metal work that makes up the appearance of the the gun. In other words, it looks great, but don't expect much in the way of performance. A notable exception is the inclusion of the A&K M249 Gearbox. It is a stout gearbox with plenty of upgrading available. The well boxed gun arrived with the gun, ammo box magazine and pintle, all neatly and securely packaged from the factory.
It appeared to had been test fired. I set up the gun and readied it for firing. When I did fire the gun, the .20g BBs just spit out the front about twenty feet...going no where. Like mentioned in other reviews about this gun, there is not an adjustable hop up. It is a fixed bucking, part of the sleeve.
I started an autopsy on the gun. It came apart nicely, held together with many machine screws. Upon removing the gearbox, I found the air nozzle on the tappet plate, was split in half. It fell out as I examined the gearbox. The next problem was found when I removed the internal barrel and hopup/feed unit. The hopup was not installed properly. The fixed bucking was not aligned with the hole in the barrel, so basically, the gun had no working hopup in that condition. Simply rotating the hopup would bring the bucking back into alignment. An easy fix.
The broken nozzle will require a gearbox disassembly. I plan on up grading at that time and installing a slightly longer barrel, as the stock barrel ends about two inches inside the outer barrel. If left stock, it would need some sort of stablization (fixed alignment) at the muzzle end as the inner barrel is obstructed by the outer barrel.
Again, I emphasize that your money is going to get you a good looking gun that is very well built. If you are lucky, your internals will be good and the gun will shoot well. The feed/hopup chamber appears to be a plastic M-16 style unit with the mounts and top machined off. You could drill a small hole and thread in a small set screw on top of the fixed hopup bucking and make it adjustable, like Viva Arms did on their version. I plan on experimenting with proper, adjustable feed and hopup chambers, seeing what will fit inside the sheet metal innards of this gun.
The ammo box magazine is good. It has a hard wire feed drive that is connected to the trigger switch. Other than that, it is a copy of the Viva Arms version. I plan on experimenting with lengthened feed tubes, so the ammo box and mount do not have to be attached to the side of the gun. I bought a repro tripod and purchased the 6MM Proshop T&E which I have not seen yet, as the shipping box contained a pintle instead. Evike is taking care of that problem now.
Not sure who actually made or imported the gun. When I paid for it last year, it was marketed as a 6MM Proshop product. The box the gun arrived in, and the current listing on Evike, list it as a EMG product. Product support from the manufactured is non existent. I am sure Evike could help if you choose to go that route with any problem or questions.
Again, a nice, well built shell of a gun with cheap internals, except for the A&K gearbox. A good gun to buy if you like to tinker and improve things.... "Got mine a few weeks ago, pre-ordered october 2015.
IT DOES NOT HAVE AN ADJUSTABLE HOPUP!
Out of the box it did not work at all, after a almost complete disassembly i found one of the connector to the motor was completely broken in half, some of the screws on the receiver had fallen of.
Fixed it and took it for a field test the following morning, the accuracy sucked big time and the bb´s did only travel about 15-20m (50-60ft)
The magazine holder is placed to far back so you can only angle it up a couple of degrees before it hits the tripod, so forget about shooting up hill or into high buildings without some modification, and its not in line with the bullet feed on the gun.
Bought an original tripod instead of the one that´s for sale with the gun, but the measurements is the same.
The charging handle is a joke and you risk shorting cables to the battery if you force it.
The inner barrel ends about 10-12 cm inside the outer barrel, and worst of all it does not have a adjustable hopup like they say, have removed the inner barrel and hop up unit from the gun and it is no way you can adjust the hopup, it is 100% fixed without modification.
It is a cool looking gun, but don´t expect to be able to take it out on the field without some modifications right out of the box. Read More Reviews Write a Review
« Back to product description
*Tripod sold separately. All guns sold in the U.S. will be sold with blaze orange tip in compliance with federal law EMG M1919 WWII American Automatic Squad Support Weapon Airsoft AEG - Limited Edition (Package: Gun and Pintle)
The M1919 is by far one of the most iconic and unique American firearms of all time. Modeled after the famous M1919 Browning machine gun, the 6mmProShop M1919 is an authentic replica of the irreplaceable American squad support weapon for WWII re-enactment and collectors. This limited edition replica, with nearly full CNC and machine milled construction, was made with the intention of producing an M1919 with the authentic look and feel of the real thing. What's exciting is that 6mmProShop redesigned the Airsoft version of the M1919 to be more than a just collector’s piece. 6mmProShop in collaboration with A&K outfitted the M1919 with a reliable M249 gearbox that is LiPo ready and fully reinforced for realistic rapid firing.On the outside the 6mmProShop M1919 boasts some hefty construction with heavyweight materials. Overall the gun alone weighs an impressive 18lbs lending a realistic feel in handling. The 6mmProShop M1919 includes a stamped steel 5000rd box magazine that sits nicely in the attached magazine tray, making it simple to mount up to a tripod and provide some serious support.
The tried and true A&K M249 gearbox was selected by the EMG team not only because it boasts some robust construction right out of the box, but it also has a large offering of compatible upgrade and replacement parts, making it possible for the first time in Airsoft history to not just own an M1919 replica, but to be able use it on a regular basis.
The 6mmProShop M1919 is a worldwide limited edition run and is surely something you don’t want to pass up on for your arsenal.
About the M1919:
The M1919 is a .30 caliber chambered medium machine gun that saw much of its life spent in the trenches, foxholes, and fields throughout World War II, the Korean War, and the Vietnam War. It was based upon the M1917 but was designed to be air-cooled, which made in turn made it the go-to crew serve weapon of choice for many years of service.
Features: Worldwide limited edition run Hefty, heavyweight fit and finish Made almost entirely from steel and aluminum parts LiPo ready A&K M249 gearbox 5000rd box magazine with built-in pressure switch (requires 4x AA batteries, sold separately) Rear sight adjustable for windage and elevation Airsoft-spec Pintle Mount included Tripod and Traverse & Elevation mechanism sold separately here at Evike.com Length:
5000rd Box Magazine (Proprietary)
380~410 FPS (Measured with 0.20g BBs)
7.4v LiPo recommended (Battery not included. Wired to the receiver with a Small Tamiya connector)
Gun, Box Magazine, Pintle Mount
M1919 Manual Available HERE Things you may need to get started: – Required to power your AEG; use a high quality battery and charger for best results. Battery and Charger – High quality precision 6mm BB’s recommended; Use 0.20g – 0.25g BB’s for best results. BB’s – Basic cleaning and lubrication maintenance help keep your Airsoft AEG in top working order. Silicone Oil
This item is currently
Out of Stock. Most out of stock items are restocked within 1-3 weeks. Some items may take longer. Please add this item to your wishlist to keep posted on its availability. Wanna chat about
EMG M1919 WWII American Automatic Squad Support Weapon Airsoft AEG (Package: Gun and Pintle)?
Have questions about this item? We monitor these comments daily, but it may be faster to
email us directly or call us at 1-626-286-0360.
Facebook about THIS with your friends! Comment for a chance to win awesome airsoft prizes. Details can be found on The Evike Facebook Fan Page HERE! Remember to leave "Also post on Facebook" checked to qualify your comment!